The Model A rifle is chambered for many of the most popular factory-loaded cartridges manufactured in accordance with U.S. industry practice. The particular caliber for each rifle is marked on the barrel. Use only factory ammunition in good condition that is compatible with the caliber of your rifle, as designated on the barrel. Please see the section on Loading and Unloading for more information on safely loading and unloading your firearm.

warning

Ammunition

Use only new, factory ammunition of the correct caliber loaded to U.S. industry standards.

Death, serious injury, and damage can result from the wrong ammunition, bore obstructions, powder overloads or incorrect cartridge components. Even the strongest firearm can be blown up by excess pressure. Always wear shooting glasses and hearing protection.

IMPROPER AMMUNITION DESTROYS FIREARMS

NOTICE: WE SPECIFICALLY DISCLAIM RESPONSIBILITY FOR ANY DAMAGE OR INJURY WHATSOEVER OCCURRING IN CONNECTION WITH, OR AS A RESULT OF, THE USE IN ANY GLENFIELD FIREARM, OF FAULTY, NON-STANDARD, "REMANUFACTURED," OR HAND-LOADED (RELOADED) AMMUNITION, OR OF CARTRIDGES OTHER THAN THOSE FOR WHICH THE FIREARM WAS ORIGINALLY CHAMBERED.

Practice the important aspects of firearm handling described below with an unloaded rifle until you can perform each of the steps with skill and confidence. Before loading the rifle, please read completely through this manual, and always be certain the muzzle is pointing in a safe direction. Do not load the rifle until you are ready to use it!

(The following procedure assumes a new rifle with the bolt removed).

1. Keep the muzzle pointed in a safe direction. (Safe Handling Step 2)
2. Position the safety selector in the “SAFE” position
3. Insert the bolt in the receiver in accordance with the “To Replace Bolt” instructions
4. Lift the bolt handle and draw the bolt fully to the rear.

Loading The Magazine:

Ensure the safety selector is in the "SAFE" position. The rifle may be loaded with the bolt in the open (fully to the rear) or closed position, but loading in the open position is the preferred method because the chamber condition can be readily and continually determined, and it requires less force to insert a loaded magazine into the rifle.

Press the magazine latch and pull the magazine down and out of the rifle. Load the desired number of cartridges into the top of the magazine. Insert the magazine into the bottom of the rifle until the magazine latches into place (a click will be heard).

NOTE: Use only as much force as is necessary to seat the magazine in the magazine well - using excess force may result in over-insertion of the magazine and cause damage and/or feeding issues.

Loading The Chamber:

The safety selector should be in the “SAFE” position if the firing pin is cocked. Do not chamber a cartridge until you are ready to shoot immediately. After inserting the magazine, push the bolt handle forward (or cycle the bolt if the bolt was closed when the magazine was inserted). This will strip a cartridge from the magazine and push the cartridge ahead of the bolt into the chamber. Close the bolt handle fully downward and move the safety selector fully rearward to the “SAFE” position if the firing pin was not previously cocked. If you would like to “top off” the magazine, you may remove it, load an additional cartridge, and reinsert the magazine into the rifle.
NOTE: With the bolt closed and a full magazine inserted, more force may be necessary to fully seat the magazine.

WARNING: DO NOT TOUCH THE TRIGGER UNTIL YOU ARE ACTUALLY READY TO FIRE THE RIFLE.

To Single-load:

Ensure the safety selector is in the “SAFE” position. Place a cartridge directly into the chamber and close the bolt.

NOTE: The rifle will fire if a cartridge is in the chamber and the trigger is pulled, whether or not a magazine is inserted. NEVER RELY UPON THE PRESENCE OF THE MAGAZINE TO DETERMINE IF THE RIFLE IS LOADED. ALWAYS CHECK THE CHAMBER!

To Fire The Rifle:

When a cartridge is chambered and the rifle is pointed in a safe direction, put the safety in the “FIRE” position. Pulling (squeezing) the trigger will discharge the cartridge. Always be certain that you know where the bullet will strike when you fire the rifle. Never allow the thumb to touch the back of the firing pin when firing, as it can be pinched when the back of the firing pin moves forward to fire the rifle.

To Unload Rifle and Magazine:

1. Ensure the rifle is pointed in a safe direction.
2. Move the safety selector to the “SAFE” position if the firing pin is cocked.
3. Remove the magazine by pressing the magazine latch rearward and pull the magazine down and out of the rifle.
4. Lift the bolt handle fully and then pull it completely to the rear to eject the chambered cartridge (if present).
5. Leave the bolt open while you visually inspect the chamber to be certain it is empty.
6. Once you are certain the chamber is empty, close the bolt fully.
7. Move the safety selector to the “FIRE” position and with the rifle pointed in a safe direction, pull the trigger.

Firearms of all makes and types are susceptible to occasional malfunctions resulting in a cartridge not feeding from the magazine to the chamber or a cartridge or fired case not being extracted and ejected.

To minimize the possibility of such occurrences, the firearm user should:

• Use ammunition of the correct caliber and type loaded to U.S. Industry Specifications.
• Do not use cartridges that are deformed or cartridges that have been reloaded.
• Clean and lubricate the firearm in accordance with the instructions in this manual.
• Learn how to correctly operate the bolt and how to properly load and empty the chamber and magazine.
• If the mechanism shows signs of not functioning correctly, or if a part is damaged or broken – don’t use the rifle. Have it inspected and repaired.

For most repairs, we recommend that Model A rifles be returned to the factory. However, if a firearm has a cartridge in it that cannot be removed, then it is a violation of Federal Regulations to ship that loaded firearm whether it be by U.S. Mail or by common carrier. In this case contact our Customer Service Department at 336- 949-5200.

If a jam or malfunction occurs, immediately put the safety selector in the “SAFE” position if the firing pin is cocked and be certain the muzzle of the rifle is at all times pointing in a safe direction.

If a jam or malfunction occurs, use the guide below to study the situation and determine the nature of the jam and how best to clear it:

• If possible, first remove the magazine first. It may be necessary to manually remove a jammed cartridge which has only partially been stripped from the magazine. If so, use extreme care.
• If the misfire is the result of a cartridge not firing or an unusual report (either louder or quieter than normal), keep the rifle pointed in a safe direction for at least 30 seconds prior to retracting the bolt.
• If a cartridge or fired case is caught between the bolt and the barrel, or against a cartridge that is in the chamber, remove the magazine. Then, retract the bolt fully and remove the jammed cartridge or case.
• If a cartridge is “stuck” in the chamber, do not use any tool that could act as a “firing pin” by impacting the primer and discharging the cartridge
• After clearing a jam, inspect the firearm mechanism to determine if dirt might be the cause of the problem. Excess lubricant or grease can cause cartridges to feed sluggishly or fail to extract. An accumulation of grease or dirt on the face of the bolt, under the extractor, in the chamber, or in the magazine can contribute to cartridge feeding problems. See section on “Care and Cleaning”
• After clearing a jam, inspect all cartridges and fired cases that have been removed from the firearm. Safely dispose of any cartridges that are in any way damaged.
• If it appears that the rifle is not at fault and that the jam was caused by the type of cartridge being used, then try another type.
• Examine your fired cartridge cases. If they have split, blown, or bulged case heads, stop using that ammunition and promptly return the rifle to the factory for examination.
• If the above procedures do not result in a smooth and reliable feeding firearm, don’t use the rifle. The Model A rifle can be returned directly to our Customer Service Department for inspection and repair, if required. See the “Service and Parts Policy” section of the manual for packing and shipping information.

View the accompanying video to this section on the online manual: https://glenfieldfirearms.com/manuals/

It is preferable to carry out these procedures on a workbench or table that has a covered top. A piece of a shallow nap rug or an old, coarse blanket is an ideal covering. Such a covering not only reduces the chances of the rifle slipping and being scratched, but also it serves to trap pins, plungers, and springs that may otherwise get lost. It is advisable to have a container – such as a shoebox – in which each part can be placed as it is removed from the firearm. Before starting disassembly, remove any attached sling, scope, and rings.

Before attempting to disassemble the rifle for the first time, study the parts drawing and parts list at the end of this manual to become familiar with the relative position, appearance, and name of each part. Carry out the disassembly slowly and carefully and note the position of the part in the firearm before starting to remove it. (Taking pictures with your cell phone during disassembly can prove very helpful.) If a part is under spring tension (such as the magazine catch) remove it cautiously and anticipate the direction the spring and plunger are most likely to “jump.”

1. Keep the rifle pointed in a safe direction!
2. Put the safety in the “SAFE” position if the firing pin is cocked.
3. Check to be certain that the chamber and magazine are empty, and remove the magazine.

4. Open the bolt and pull it to the rear while at the same time pressing on the rear of the bolt stop, which is located on the left side of the receiver. Remove the bolt fully from the rear of the receiver and release the bolt stop. For routing cleaning, the rifle does not need to be disassembled further.

   

To Remove The Bolt Shroud:

NOTE: DO NOT ROTATE THE FIRING PIN BACK BEYOND THE POSITIONS SHOWN IN THESE INSTRUCTIONS. If the firing pin back is turned too far in either direction, it will “fall down” to the bottom of the cocking cams. It will take significant effort, and possibly the use of hand tools or a gripping aid, to return the firing pin back to the correct cam notches. Please note that the firing pin back will only rotate clockwise, relative to the bolt body (when viewed from the rear of the bolt). Because there are dual cocking cams, you may need to rotate the firing pin back up the cams twice in order to return the firing pin back to its proper position.

To Remove the Barreled Action from the Stock:

1. Use a 3/16" Allen wrench to loosen and remove the two hex screws in the bottom of the stock.
2. Remove the magazine well. (If Equipped)
3. Lift the barreled action out of the stock.

Adjusting The Trigger Pull Weight

The trigger pull weight on the Model A rifle can be adjusted from approximately three pounds to approximately five pounds. It is suggested that you familiarize yourself with the trigger's pull weight by dry firing the rifle before live ammunition is loaded or fired, ensuring the magazine is removed, the chamber is empty, and the rifle remains pointed in a safe direction.
Always check your rifle's function after adjusting the trigger pull weight.

To access the pull weight set screw, remove the barreled action from the stock. The set screw is located on the outside, forward edge of the fire control housing. (See Pull Weight Set Screw.) The screw can be turned using a 3/32” Allen wrench. Note that the screw is treated with a thread locking compound that can make the screw difficult to turn. Threading the screw in (turning clockwise) will increase the trigger pull weight, threading the screw out (turning counterclockwise) will reduce the trigger pull weight. Approximately six full turns of the screw represents the entire range of trigger pull weight adjustability. Turning the screw beyond this amount will not further increase or decrease trigger pull weight, and turning the screw too far in may cause the trigger to bind and not function. Turning the screw too far out may prevent the barreled action from reassembling to the stock. We suggest turning the screw in no more than 1/2 revolution increments and testing the pull weight before further adjustment is attempted.

Be Sure Rifle Is Unloaded

View the accompanying video to this section on the online manual: https://glenfieldfirearms.com/manuals/

To Replace The Stock:

1. Place the barreled-action assembly into the stock. Be certain the two angled bedding blocks in the stock fit into the corresponding grooves in the receiver. (See Stock Replacemnt 1.)
2. Insert the magazine well back into the bottom of the stock. (If Equipped)
3. Loosely install the screws into the bottom of the stock and thread them into the barreled action, using the included allen wrench.
4. Alternate tightening each screw – a partial turn at a time – so that the screws are tightened equally until both are snugly tightened to 60-80 in-lbs. Do not tighten one screw all the way and then the other.

To Replace The Bolt Shroud:

1. With the bolt shroud held approximately 1/4" to the rear, insert it over the firing pin back. (See Bolt Shroud 1.)
2. Push the bolt shroud forward until it is flush with the bolt body. (See Bolt Shroud 2.)
3. Grasp the outside of the bolt shroud and firing pin back and rotate them approximately 30˚counterclockwise (See Bolt Shroud 3) so the firing pin back lobe is at rest inside the notch on the cam. (See Bolt Shroud 4.)

NOTE: The firing pin back must be aligned with the center of the bolt handle to reinstall the bolt shroud. (See Bolt Shroud 3.)

NOTE: Do not rotate the firing pin back beyond the positions shown in these instructions. If the firing pin back is turned too far in either direction, it will “fall down” to the bottom of the cocking cams. It will take significant effort, and possibly the use of hand tools or a gripping aid, to return the firing pin back to the correct cam notches. Because there are dual cocking cams, you may need to rotate the firing pin back (clockwise) up the cams twice in order to return the firing pin back to its proper position.

---

To Replace The Bolt

1. Ensure that the chamber is empty and no magazine is inserted! Keep the rifle pointed in a safe direction! Put the safety selector in the “SAFE” position.
2. With the bolt positioned so the firing pin back is at the 12 o'clock position (See Bolt Replacement 1), and the bolt head away from you, insert the bolt into the receiver.
3. As the bolt handle gets closer to the receiver, rotate the bolt to the right so that the bolt handle is aligned with the bolt channel on the right hand side of the receiver. (See Bolt Replacement 2.)
4. Push the bolt fully forward, then rotate the bolt handle down to lock the bolt closed. (See Bolt Replacement 3.)
5. Cycle the bolt to ensure it is moving smoothly within the receiver.

---

NOTE REGARDING ACCURACY: The accuracy of any rifle can vary depending upon the caliber and type of cartridges used. If your Model A rifle does not perform to expectations, it is advisable to first try several brands and types of cartridges to determine which one delivers the best accuracy. If your rifle still is not as "accurate" as you believe it should be, run the following checks:

1. Be certain the two bedding screws are snugly tightened to 60-80 in-lbs. as described in Step 4, of the "To Replace The Stock" instructions above.
2. Be certain the bore is clean and free from accumulated metal fouling, deposited by metal jacketed and lead bullets. Review the “Care and Cleaning” section.
3. Check the scope base and scope ring screws for tightness, setting, and alignment.
4. DO NOT alter the stock bedding in any way. Do not scrape away polymer or bed the stock with "glass," plastic, epoxy, etc. Once a rifle stock has been altered, it cannot be reworked by our Customer Service Department.

If everything is tight, the bore is clean, the scope is properly aligned and secure, but the accuracy problem persists, please contact our Customer Service Department or call 336-949-5200. Fully describe all circumstances and conditions involved.

Periodic inspection of any firearm is important to ensuring its safe operation. It is important to clean and inspect your firearm after each range session or whenever the firearm has been exposed to sand, dust, moisture, humidity, or other adverse conditions. Proper maintenance increases the longevity of your firearm and will allow early detection of worn or broken parts.

Prior to each use, visually inspect the firearm to ensure no components are damaged, missing, loose, bent, cracked, chipped or peened. If you observe excessive wear, you should stop using your rifle and contact Customer Service or a trained, certified gunsmith to evaluate its condition and replace any worn parts, if necessary.

After any disassembly and reassembly, it is important to verify that the action is working correctly before any live firing is attempted.

To Check Your Rifle's Function:

1. BE SURE THERE IS NO AMMUNITION IN THE CHAMBER OR THE MAGAZINE AND KEEP THE RIFLE POINTED IN A SAFE DIRECTION!
2. Check the Bolt Function and Firing Pin Action: With the magazine removed, cycle the bolt open and closed three times. The bolt should operate smoothly and travel freely within the receiver without binding. Next, close the bolt and ensure that the safety is in the “FIRE” position. With the rifle pointed in a safe direction, pull the trigger and listen for the firing pin release ‘click’ as an indication the firing pin is functioning correctly. Repeat this process two more times.
3. Check the Safety: With the magazine removed, cycle the bolt into battery but do not dry fire the rifle.
   • Place the safety in the rearmost “SAFE” position and attempt to pull the trigger. With the safety in this position, the firing pin should NOT dry fire and the ‘click’ referenced above should NOT be heard.
   • Move the safety selector to the forward-most “FIRE” position. Pull the trigger. The firing pin should dry fire with a ‘click’ sound, and you should be able to cycle the bolt.
4. Check for Smooth Magazine Follower Movement: With the magazine removed from the rifle, use a small tool such as a pin punch, pen cap, or small screw driver to press the magazine follower (the formed plate in the magazine that pushes the cartridges upward for feeding) down and release it. The follower should freely move within the magazine and return to the top
5. Check Magazine Latching: With the bolt open, insert an EMPTY magazine into the magazine well and push the magazine until the latch is engaged. The latch should securely lock the magazine in place with a ‘click.’ Inspect the magazine to verify that it latched securely by pulling on it with moderate force without pressing the magazine release. The magazine should remain locked into the rifle.

If any of the above function checks fail, please consult a competent gunsmith or contact Customer Service at 336-949-5200 for further firearm inspection before using the firearm.

View the accompanying video to this section on the online manual: https://glenfieldfirearms.com/manuals/

A firearm must be free of rust, dirt, grease, and firing residues to function safely and reliably. Periodic maintenance, which includes inspection of components to determine if they are in proper working order, is absolutely essential. Firing the rifle deposits particles of bullet, lubricant, and powder in the bore, chamber, bolt, receiver, magazine, and other parts of the rifle. There is no fixed rule as to how frequently the cleaning should be carried out, but the alert firearm owner soon learns that any firearm functions most reliably and accurately when it is free of accumulations of grease and other firing residues.

Basic Cleaning Equipment Includes:

• Cleaning Rod
• Bore Brushes with a Tip on Which a Cloth Patch Can Be Inserted
• Patches
• Powder Solvent
• Lubricant
• Small, Lint-Free Cloths
• Toothbrush
• Commercially Available Bore Cleaning Solution

CAUTION: THE USE OF CAUSTIC OR ACETONE-BASED CLEANERS ARE NOT RECOMMENDED AS THE SOLVENT MAY HARM THE FINISHED SURFACES, PLASTICS, LAMINATES, COMPOSITES, RUBBER PADS, OR OTHER MATERIALS USED IN THE CONSTRUCTION OF YOUR FIREARM. BEFORE CLEANING YOUR FIREARM, ALWAYS TEST THE CLEANING AGENT/SOLUTION IN AN INCONSPICUOUS AREA ON ANY PART YOU ARE GOING TO CLEAN WITH IT (INCLUDING, BUT NOT LIMITED TO, THE STOCK AND EXTERIOR PORTIONS OF THE BARREL AND RECEIVER) TO ENSURE IT WILL NOT HARM THE FINISH. NEVER USE AUTOMOTIVE OR PAINT STRIPPING PRODUCTS TO CLEAN YOUR FIREARM.

Note: For routine cleaning, it is necessary only to remove the bolt and magazine.

To Clean The Rifle:

1. Push-pull a properly sized, solvent-wetted patch through the bore several times. Larger sized patches will bind in the bore and can be very difficult to remove.
2. Using a solvent-wetted brush, run it the full length of the bore as many times as is necessary to completely remove all foreign matter from the bore and chamber.

NOTE: Insert the rod from the chamber end of the barrel and push firmly so the brush or patch emerges from the muzzle. Don’t reverse the rod when a brush or patch is being used before the brush or patch exits the muzzle – it may bind. Don’t use patches or brushes dripping with solvent or oil. Use rod and brushes with care so as not to damage the firearm.

3. Dry the bore with clean patches and examine it. If the bore remains fouled, repeat the brushing.
4. Complete the cleaning by dry patch wiping the bore and chamber.
5. Use a clean, solvent-wetted patch to remove firing residue and dirt from all “reachable” surfaces inside the receiver.
6. Use the solvent-wetted toothbrush to dislodge caked dirt from all parts of the bolt assembly and from surfaces inside the receiver that can’t be reached with a patch.
7. Use cleaning patches or the cloth to remove the solvent.
8. If lifting the bolt handle becomes difficult or requires more force than usual, remove the bolt shroud (See Disassembly step 4) and clean and lubricate the bolt cocking cam surfaces.
9. Wipe all surfaces – internal and external – with a very light coat of oil. Oil and similar preparations “collect” dirt particles which can interfere with reliable functioning of the rifle. Therefore, use these preparations very sparingly. A drop of oil applied to the bolt assembly components, the pivot points of the trigger mechanism, the safety, the bolt stop and the magazine latch, will work into all the parts that need lubrication.
10. While cleaning the stock, avoid the use of cleaning solvents containing acetone, as they can damage the finish of your stock, particularly if the stock has a painted finish or camo-dipped pattern.
11. Reassemble the rifle and carefully wipe off all excess solvent, lubrication and preservative preparations from the rifle.
12. If the rifle will be stored for an extended period, clean the rifle thoroughly. Disassemble to the extent described in the Disassembly section of the manual, taking care to put pins and similar easily mislaid and “rolling” components in a tray. Re-wipe all surfaces with preservative oil. Reassemble and store properly.

Firearms and components made of stainless steel are relatively more resistant to corrosion than those of blued steel. However, in the interest of proper operation and longevity of stainless steel firearms and components, inspect them frequently and clean, lubricate and apply an appropriate rust preventative. Sometimes, discoloration occurs from perspiration or from contact with some types of firearm cases. Rusting may occur as a result of the firearm being exposed to moisture, salt air or chemicals.

Minor discoloration can usually be removed by rubbing the stainless area with an abrasive ink eraser, crocus cloth, or a “metal polishing” compound. When using any of these abrasives, proceed with care and use light pressure to achieve a blending of “color” with those areas that are not discolored.

External surfaces most subject to rusting from handling, or from exposure to the elements, should be cleaned and wiped dry after use or after exposure to adverse conditions. If the rifle is to be stored, coat it with a light film of oil or preservative. If the rifle is in regular use, and the presence of oil or grease is objectionable, the external surfaces can be coated (after cleaning and drying) with a paste wax formulated for use on metals. Apply the wax sparingly, allow time for it to dry hard, then buff lightly with a soft cloth. When applying the wax, take care that it does not get into the mechanism, on the functioning parts or in the bore.

Firearms and components, both metal and polymer, may be finished with Cerakote. Cerakote is a polymer-ceramic composite coating that provides an attractive, durable, corrosion, and chemical-resistant surface on your rifle. These finishes vary in color and composition, but all provide excellent protection when properly maintained.

Cerakote can be cleaned using a soft brush or rag and mild solvent or detergents to remove soil and fouling from the surface. Do not use hard metallic brushes or aggressive solvents that might damage the finish or underlying material.

Finish by applying a light coating of gun oil on all surfaces with a soft rag or patch.

Magazines for your Model A Rifle may be purchased at ShopRuger.com or your local independent retailer of Glenfield firearms.

The Model A rifle is drilled and tapped for standard Weaver #46 scope bases which accept a variety of scope rings. Please follow the instructions provided with your rings and bases.

Care has been taken to ensure that threads are concentric to the bore to allow mounting of common muzzle devices. Factory installed muzzle devices are most commonly secured to a torque setting against the shoulder of the barrel or by use of a jam nut to maintain device timing.

For other muzzle devices, ensure the correct thread diameter and pitch and bore size larger than the caliber of the rifle, and follow the manufacturer's recommended installation instructions.

Most threads are common across a wide range of calibers, with some exceptions as noted. If something does not feel right in the first revolution of device installation, stop and inspect both the device and muzzle to avoid damage to the device or threads. For calibers not specifically listed, call Ruger Customer Service at 336-949-5200.

Thread Patterns

Firearms Should Not Be Stored Loaded!

If you have any questions regarding the performance of your Model A rifle, please contact Customer Service or call 336-949-5200. Fully describe all circumstances and conditions involved. If you should need to return your rifle to the factory for repair, or order parts for it, please comply with the information in the following sections.

NOTE: You must obtain a Repair Authorization Number before returning your firearm. An authorization number can be obtained by contacting Customer Service or calling the Customer Service Department at 336-949-5200. Firearms should be sent prepaid. We will not accept collect shipments.

The Federal Gun Control Act, as well as the laws of most states and localities, do not prohibit an individual (who is not otherwise barred from purchasing or possessing a firearm) from shipping a firearm directly to the manufacturer for repair. However, before you ship your firearm to us, be certain that your state or locale does not have a law or regulation that will prohibit you from receiving the firearm (or any included magazines) from us after repair. If such receipt is prohibited, please have a federally licensed firearms dealer ship the firearm to us. If your firearm is sent to us by a dealer, it will be returned to that dealer after being repaired. If a handgun (pistol or revolver) is shipped by an individual who does not hold a Federal Firearms License, it must be shipped for overnight delivery via U.P.S., Federal Express or other, similar private overnight service.

NOTE: Persons who do not hold a Federal Firearms License are prohibited by Federal law from shipping a handgun by U.S. Mail. Handguns mailed in violation of the law may be impounded or confiscated by the Post Office and the non-FFL may be subject to prosecution. Rifles and shotguns may be shipped via U.S. Mail.

Please do not include rifle cases, slings, telescopic sights, or custom accessories with a firearm being shipped to the factory for service. DO NOT SEND FIREARM BOXES OR LITERATURE THAT YOU CONSIDER TO BE COLLECTOR’S ITEMS. Always insure your shipment.

All work performed is subject to a minimum labor charge and charges for shipping and handling. Most models can be refinished, but custom gunsmithing service or nonstandard alterations are NOT AVAILABLE from Customer Service. Please contact the Customer Service for pricing information.

Please contact our Customer Service Department at 336-949-5200 for parts availability and current prices or use our Online Support Request to request for assistance with your firearm.

Payment in full via credit card (Visa, MasterCard, Discover or American Express), money order, or certified bank check (no personal checks or cash, please) is required before any service will be performed. All parts orders are subject to a minimum charge and charges for shipping and handling. There is a minimum charge plus a shipping and handling charge for non-warranty factory fit parts. All factory fit parts are fit on an exchange basis only. We will not return the replaced parts. Please contact the Customer Service Department for pricing information.

Because the receiver of the Model A rifle is a serial numbered component, it is defined as a “firearm” by Federal law and is not sold as a separate component.

Parts designated by an asterisk must be factory fit. These parts are fit on an exchange basis only. We will not return the replaced parts. We will not return any part that is broken, malfunctioning, badly worn or has been modified.

We believe that Americans have a right to purchase and use firearms for lawful purposes. The private ownership of firearms in America is traditional, but that ownership imposes the responsibility on firearm owners to use their firearms in a way that will ensure their own safety and that of others. When firearms are used in a safe and responsible manner, they are a great source of pleasure and satisfaction, and represent a fundamental part of our personal liberty.

Firearms do not cause accidents! Firearms accidents are almost always found to have been the result of carelessness or ignorance on the part of the shooter of the basic rules of safe firearm handling.

The following rules must be observed by firearm users at all times. Safe firearm handling is not just desirable, it is absolutely essential to your safety, the safety of others, and the continuation of firearm ownership and sport shooting as we know it today.

1. LEARN THE MECHANICAL AND HANDLING CHARACTERISTICS OF THE FIREARM YOU ARE USING.
Not all firearms are the same. The method of carrying and handling firearms varies in accordance with the mechanical provisions for avoiding accidental discharge and the various proper procedures for loading and unloading. No one should handle any firearm without first having thoroughly familiarized themselves with the particular type of firearm they are using, and with safe firearm handling in general.
2. ALWAYS KEEP THE MUZZLE POINTED IN A SAFE DIRECTION.
Be sure of the bullet stop behind your target, even when dry-firing. Never let the muzzle of a firearm point at any part of your body or at another person. This is particularly important when loading or unloading a firearm. In the event of an accidental discharge, no injury can occur as long as the muzzle is pointing in a safe direction. A safe direction means a direction that will not permit a discharged bullet to strike a person, or to strike an object from which the bullet may ricochet.
A safe direction must take into account the fact that a bullet may penetrate a wall, ceiling, floor, window, etc., and strike a person or damage property. Make it a habit to know exactly where the muzzle of your firearm is pointing whenever you handle it, and be sure that you are always in control of the direction in which the muzzle is pointing, even if you fall or stumble. Keep your finger off the trigger until you are ready to shoot.
3. FIREARMS SHOULD BE UNLOADED WHEN NOT IN USE.
Firearms should be loaded only when you are in the field or on the target range or shooting area, ready to shoot. Firearms and ammunition should be securely locked in safes, racks or cabinets, or by using the locking device supplied with the firearm, when not in use. Ammunition should safely be stored separate from firearms. Store your firearms out of sight of visitors and children. It is the firearm owner’s responsibility to be certain that children and persons unfamiliar with firearms cannot gain access to firearms, ammunition or components.
4. BE SURE THE BARREL IS CLEAR OF OBSTRUCTIONS BEFORE SHOOTING.
Even a bit of mud, snow or excess lubricating oil or grease in the bore may cause the barrel to bulge, or even burst on firing, and can cause serious injury to the shooter and bystanders. Be sure that you are using ammunition of the proper caliber and loading for the firearm you are using. If the report or recoil on firing seems weak, or doesn't seem quite right, CEASE FIRING IMMEDIATELY, unload your firearm, and check to be sure that no obstruction has become lodged in the barrel. Never try to shoot out an obstruction!
5. BE SURE OF YOUR TARGET BEFORE YOU SHOOT.
Don’t shoot unless you know exactly where your bullet is going to strike. Be sure of the bullet stop behind your target, even when dry-firing with an unloaded firearm. If you are in the field hunting, do not fire at a movement or noise. Take the time to be absolutely certain of your target before you pull the trigger.
6. WEAR SHOOTING GLASSES AND HEARING PROTECTION WHEN YOU SHOOT.
All shooters should wear protective shooting glasses and adequate hearing protection when shooting. Exposure to shooting noise can damage hearing, and wearing adequate eye protection when shooting is essential.
7. NEVER CLIMB A TREE OR FENCE WITH A LOADED FIREARM.
Put the firearm down carefully before climbing a fence, and unload it before climbing or descending a tree or jumping over a ditch or other obstruction. Never pull or push a loaded firearm toward yourself or another person. When in doubt, or whenever you are about to do anything awkward, unload your firearm!
8. DON'T SHOOT AT A HARD SURFACE OR AT WATER.
Bullets can glance off many surfaces like rocks or the surface of water and travel in unpredictable directions with considerable velocity.
9. NEVER TRANSPORT A LOADED FIREARM.
Firearms should always be unloaded before being moved or placed in a vehicle. A suitable carrying case or scabbard should be used to carry an unloaded firearm to and from the shooting area.
10. AVOID ALCOHOLIC BEVERAGES WHEN SHOOTING.
Don't drink until the day's shooting is over. Handling firearms while under the influence of alcohol in any form, or medications that could affect your judgement or coordination, constitutes a criminal disregard for the safety of others.

WHY NO WARRANTY CARD HAS BEEN PACKED WITH THIS NEW GLENFIELD FIREARM

The Magnuson-Moss Act (Public Law 93-637) does not require any seller or manufacturer of a consumer product to give a written warranty. It does provide that if a written warranty is given, it must be designated as "limited" or as "full" and sets minimum standards for a "full" warranty. Sturm, Ruger & Company, Inc. has elected not to provide any written warranty, either "limited" or "full," rather than to attempt to comply with the provisions of the Magnuson-Moss Act and the regulations issued thereunder. There are certain implied warranties under state law with respect to sales of consumer goods. As the extent and interpretation of these implied warranties varies from state to state, you should refer to your state statutes. Sturm, Ruger & Company wishes to assure its customers of its continued interest in providing service to owners of Glenfield firearms.